超音速电弧喷涂在循环流化床锅炉水冷壁中的应用探讨

分析循环流化床锅炉水冷壁失效的原因,提出对炉管进行防磨喷涂的修复方案.比较几种不同喷涂技术的性能,介绍超音速电弧喷涂技术的特点、喷涂材质的选择及工艺流程.应用超音速电弧喷涂技术修复循环流化床锅炉水冷壁,经过2个100d长周期运行后,涂层完好均匀,厚度没有减薄.     

Surface characterization of 8‐quinolinyl acrylate‐grafted poly(ethylene terephthalate) prepared by plasma glow discharge and it's antibacterial activity

Poly(ethylene terephthalate) (PET) film was exposed to oxygen plasma glow discharge to produce peroxides on its surface. These peroxides were then used as catalysts for the polymerization of 8‐quinolinyl acrylate (QA) to prepare the PET grafted with QA (PET‐Q). The surface‐modified PET was characterized by attenuated total reflection Fourier transform infrared spectroscopy (ATR‐FTIR) and X‐ray photoelectron spectroscopy (XPS). The introduction of QA to the PET surface was confirmed by observing the presence of nitrogen in the XPS survey scan and high‐resolution spectra. The amount of QA grafted on to the PET surface as measured by the gravimetric method was about 5.2 μg cm^?2. The antibacterial activity of the surface‐modified PET texture was investigated by using a shake‐flask and an inhibition zone test method. After 6 h of shaking, the PET grafted with QA showed the inhibition (91%) of the growth of the gram‐positive microorganism, S. aureus. Even after laundering ten times, an effectiveness of the inhibition was found. However, little inhibition was shown with the gram‐negative microorganism, K. pneumoniae. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 863–868, 2006     

放电等离子制备Ti3AlC2/TiB2复合材料及性能

采用放电等离子烧结(spark plasma sintering,SPS)工艺制备了Ti3AlC2/TiB2复合材料,并研究了复合材料的性能.研究表明:在1 250℃,30MPa烧结8min,可以获得相对密度达98%以上的致密Ti3AlC2/TiB2块体材料;在Ti3AlC2中添加TiB2能大幅度提高材料性能,当TiB2含量为30%(体积分数,下同)时,Ti3AlC2/30%TiB2复合材料的Vickers硬度达到10.39GPa,电导率为3.7×106 S/m;当TiB2含量为10%时,抗弯强度为696MPa,断裂韧性为6.6MPa·m1/2.用电子显微镜对复合材料的显微结构分析表明:Ti3AlC2/TiB2复合材料的晶粒为层状结构.     

Photocatalytic mineralisation of organic compounds: a comparison of flame-made TiO2 catalysts

A comparative photocatalytic analysis was carried out on TiO₂ made in a Flame Spray Pyrolysis (FSP) process and flame-made Degussa P25. Both have similar crystallinity, phase composition, phase segregation and a non-porous surface. Hence comparison was made based on their difference in specific surface area, organic adsorption and the amount of OH• generated upon illumination. The photocatalytic activity tests were carried out using the following series of organic compounds: sucrose, glucose, fructose, maleic acid, glyoxylic acid, oxalic acid, isobutyric acid, phenol and methanol. FSP-made TiO₂ outperformed P25 for saccharides mineralisation, while for phenol and methanol mineralisation P25 was better than FSP-made TiO₂. Similar mineralisation rates were observed for both FSP-made and P25 TiO₂ for the mineralisation of carboxylic acids. This shows that the relative performance of the photocatalysts depends on the type of organic compounds to be degraded. The high surface area and possibly a more efficient interfacial charge transfer of FSP-made TiO₂ provided an efficient pathway for saccharides mineralisation. As for phenol and methanol, the mineralisation rates were higher when using P25 due to the greater amount of OH• radicals generated by this photocatalyst. The fast mineralisation rates of carboxylic acids made degradation of these organic compounds to be less affected by the TiO₂ photocatalyst properties and conditions tested in this work.     

ICP-AES法测定精制盐水中的微量元素

采用电感耦合等离子体发射光谱法测定二次精制盐水中Ca、Mg、Sr、Fe、Ba、S i等微量元素含量。方法简便、快速、精密度高,结果准确可靠。     

静电喷涂技术在溶剂型涂料中的应用

介绍了静电喷涂的原理、工艺和静电漆料的配方设计原则，从理论和实践上证实了静电喷涂工艺具有较好的经济效益和环境效益。     

喷雾干燥的节能分析

喷雾干燥是能耗较大的单元操作,节能工作十分重要。对喷雾干燥过程中的热量分配作了计算分析,并根据作者对喷雾干燥过程的研究及编制的程序对各种操作因素对干燥过程能耗的影响进行了分析评价,给出了干燥过程的节能措施。     

放电等离子烧结钛/氧化铝的界面反应

研究了用放电等离子烧结的Ti/Al2O3在1 200℃和30MPa条件下界面反应特性,用X射线衍射和电子探针微区分析了界面反应类型.结果表明:Ti/Al2O3界面反应为反应扩散型,即氧化铝首先发生分解,分解出的Al原子扩散进入Ti中,扩散距离约为62 μm,界面处Al原子的摩尔分数x高达42.49%,Ti与Al在界面区发生反应,在贫Al区生成Ti3Al相,贫Ti区生成TiAl相等界面产物,O原子固溶于Ti中.     

Surface crosslinking of high‐density polyethylene beads in a modified plasma reactor

High‐density polyethylene (HDPE) beads were successfully surface‐crosslinked in a modified plasma reactor. The modified plasma reactor treats large amounts of beads, which are uniformly surface‐crosslinked. In this study, effects of the gas pressure, radio‐frequency (RF) power, and the treatment time on the degree of surface crosslinking were systematically investigated. Degree of surface crosslinking was measured by solvent extraction method (boiling xylene method, BXM). The gel content of plasma‐treated HDPE increases from 0.0 to 1.05% within 10 min at 100 mTorr, 200 W. FTIR and DSC analyses show that the crosslinked layer after plasma treatment is limited only at HDPE surface without changing the bulk thermal property of HDPE. Through the analysis of FTIR, it was confirmed that main peaks corresponding to CH₂ bands were decreased and two peaks corresponding to CF₂ and CF₃ were observed after plasma surface modification. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2921–2929, 2002; DOI 10.1002/app.10295     

Wetting properties of polystyrene ionomers treated with plasma source ion implantation

The wetting properties of polystyrene‐based ionomers treated with plasma source ion implantation (PSII) were investigated by the measurement of water contact angles. When sulfonated ionomers were aged for a few days, the hydrophobic recovery for the ionomers became much slower than that for the nonionic polymers. However, when the samples were aged over 20 days, the water contact angle of the ionomers converged with that of the nonionic polymer. Thus, it was concluded that the ionic interaction between the ionic groups and the presence of ionic groups together resulted in the slow hydrophobic recovery and that the aging effect was significant for the ionomers. For the methacrylate ionomer of low ion content, on the other hand, it was found that the PSII treatment produced only a small change in hydrophobic recovery behavior. Thus, it was suggested that the low ionic content coupled with the small size of the ionic unit might cause changes only of a very insignificant degree in hydrophobic recovery behavior. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2500–2504, 2002